Anchoring Wood to a Steel I-Beam

Synopsis: Steel beams can carry much more weight than solid or engineered lumber, so they’re often used in home building. But anchoring wood to steel can be time-consuming. John has replaced the most common method — packing the web with lumber — with a far faster method incorporating top-mount joist hangers. By bolting a piece of lumber to the top flange of the I-beam and nailing the joist hangers to it, you can reduce the amount of lumber you use, the number of holes you drill, and the number of bolts you install. And top-mount joist hangers require fewer nails, too.

Modern floor plans are trending toward wide open spaces. Despite advances in engineered-wood beams, there are times when something stronger is needed. Many carpenters shy away from steel because fastening lumber to steel can be tricky. Cutting a steel beam on site is even trickier. Sometimes, though, a steel I-beam is the best choice. Structural steel costs less than comparable LVLs, is strong, and is available from local suppliers. If you order it to the right size with fastener holes punched, your only challenge will be attaching the lumber.

Steel has a few limitations

Although a piece of steel carries a larger load over a longer span with less depth than any other building material, steel has some disadvantages. First, it’s very heavy. You need to make sure you can get it to where it needs to go, either with humans or with a machine. Second, you won’t find steel span charts in a codebook; steel usually needs to be sized by an engineer. Steel should be protected from moisture to prevent rust and deterioration. Also, a steel beam will fail much more quickly and catastrophically than an equivalent wood beam in a fire.

Top-mount joist hangers are the most practical

In the simplest usage, an I-beam rests in pockets cast in foundation walls, with floor joists on top of it. More often, though, wood is bolted to the web; then joists or rafters are attached to the wood with standard joist hangers. The drilling and bolting required by this method are so impractical that it’s worth changing before construction. Another attachment method is to weld top-mount hangers to the I-beam. However, this option is rare, not because it doesn’t work but because most framing crews don’t have a welder on site.

I think the best method is to bolt 2x lumber to the top flange of the I-beam, then nail top-mount joist hangers to the lumber. I use 1⁄4-in. by 1 1⁄2-in. lag bolts through the bottom of the top flange. Because top-mount joist hangers won’t resist twisting as well as face-mount hangers, I use strapping below or blocking between the joists. If uplift resistance is needed, I tack the lumber in place with a powder-actuated nailing tool, then through-bolt after the plywood subfloor is down, recessing the bolt heads into the plywood.

The steel I-beams most often seen on job sites are called W- (wide) and S- (standard) shapes, depending on the width of the flange. Steel beams are designated by shape, depth, and weight. For example, a W8x35 beam is a W-shape about 8 in. deep and weighing 35 lb. per lin. ft.

Because steel is hard to cut and drill on site, your supplier needs the exact length along with sketches showing all hole locations and sizes. If you have to cut a beam, an acetylene torch is the easiest method, but metal-cutting blades in circular saws and reciprocating saws work, too.

From Fine Homebuilding #180

For more illustrations and details, click the View PDF button below:

Fine Homebuilding Recommended Products

Speed Square

When it comes to framing, it doesn’t get much more fundamental than a speed square — and with its sturdy metal build, Swanson’s will not let you down. Some of our team members have had theirs for 20 years.

Buy at Amazon

Stabila Extendable Plate to Plate Level

This level raises the bar for accuracy and quality. The extensions are designed to contact and plumb from bottom to top plates, avoiding studs that may be bowed.

Buy at Amazon

Guardian Fall Protection Pee Vee

This tool is a gem! You can use it to align plates with your snapped lines, and it’s especially helpful when working alone.

Buy at Amazon